CADDX NX-8 Manuel d'utilisateur

NetworX™ Series NX-148E-CF Commercial Fire LCD Keypad User manual

NX-148E-CF 8ARMING YOUR SYSTEM IN THE “STAY” MODE STAY is utilized when the user is inside the premise and wants protection around the perimeter. T

NX148E-CF 9USING THE QUICK ARM The Quick Arm feature may be used if it is enabled. Quick Arm will allow the user to arm the security system in the AWA

NX-148E-CF 10CANCEL / ABORT FEATURE (Optional, if programmed) The cancel light will flash during an abort delay time. If a code is entered followe

NX148E-CF 11If you do not know the number of the zone you wish to bypass, use the following steps: Step 1 Press r • The description for zo

NX-148E-CF 12Select an Option Press  for Help Auxiliary Key - If programmed, you can activate the auxiliary alarm by pressing the Emergency Activat

NX148E-CF 13VIEW ZONE STATUS Step 1 Press r • . The LCD Screen will display the zone status. Step 2 Use the • – scroll keys to browse th

NX-148E-CF 14DISPLAY TEST FUNCTION This function will perform a test of the LCD display. No alarms or reports will be sent. Step 1 Press r 4

NX148E-CF 15CHANGING USER CODES Step 1 Press r 5 . The LCD Screen will prompt for a code. Step 2 Enter [master code]. The LCD Screen will

NX-148E-CF 16PROMPT Outputs used? » DO NOT CHANGE THIS SEGMENT! Open / Close Rprt? Bypass enable? Arm / Disarm? (These are for use by a pro

NX148E-CF 17 Open 75 9/25 17:57 P3* READING THE EVENT LOG The control panel has an event log that can be retrieved using a master code. This

UP & DOWN SCROLL KEYS POWER light is “on” when AC power is present, flashes to indicate a low battery condition. 5 FUNCTION KEYS The door (not sh

NX-148E-CF 18SETTING THE SYSTEM CLOCK Step 1 Enter r 9 7 . The LCD Screen will prompt for a code. Step 2 Enter [master code]. The

NX148E-CF 19PARTITIONED SYSTEMS OPERATION This system is “ is not “ partitioned. If your system is multi-partitioned and the keypad resides

NX-148E-CF 20This display is reflecting all 8 areas are Ready, and Area 5 is disarmed. NOTE: If a number is flashing on the Armed line, that area i

NX148E-CF 21 OPERATING INDIVIDUAL AREAS IN THE MULTI-PARTITION MODE Enter a code that is a valid arm/disarm code for the area you wish to operate. T

NX-148E-CF 22KEYPAD CONTROL TONES (BEEPS) A sounder is built into the keypad and may sound for any of the following reasons:  Beeps for all ke

NX148E-CF 23SERVICE DISPLAY The following message will be displayed periodically if the security system requires service. Call your service provider

NX-148E-CF 24Expansion Box tamper A box containing an expansion device has been opened. Expansion Low Battery An expansion power supply has a low ba

NX148E-CF 25APPENDIX A - EVENT LOG NOTE: Your system may not have all of the features listed in this table. DISPLAY DESCRIPTION TXlobat Transmitter

NX-148E-CF 26DISPLAY DESCRIPTION Cancel Cancel System is disarmed and the Cancel button was pressed within 5 minutes of an alarm. Gnd Flt Ground F

NX148E-CF 27EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition. For example, the follo

NX-148E-CF 1Installing/Service Company For Service Call Central Station This system is  is not  partitioned. EMERGENCY ACTIVATION K

SYSTEM NOTES

NX-148E-CF USERS MANUAL NX148ECFUB03 REV B (MAY2003)

NX-148E-CF 3TABLE OF CONTENTS GLOSSARY OF TERMS... 4 UNDERSTANDING THE LIGH

NX-148E-CF 4THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SECURITY

NX148E-CF 5GLOSSARY OF TERMS Abort Delay: An option that allows a delay in reporting to the central station. Authority Level: The level of access a

NX-148E-CF 6UNDERSTANDING THE LIGHTS Armed Light The armed light is “on” when the system is armed. The armed light is “off” when it is disarmed.

NX148E-CF 7KEYPAD FUNCTIONS ARMING YOUR SYSTEM IN THE “AWAY” MODE AWAY is utilized when the user is going away from the premise and wants the interio